H3c-technologies H3C MSR 800 Uživatelský manuál

H3C MSR800 RoutersInstallation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6W101-20140604

3 • Install a lightning arrester at the input end of the power supply. Installation accessories and tools Figure 1 and Figure 2 list the accessories

4 Item Requirements Yes NoTemperature 0°C to 40°C (32°F to 104°F) Relative humidity 5% to 90% (noncondensing) Cleanness Dust concentration ≤ 3 ×

5 Installing the router WARNING! To avoid injury, do not touch bare wires, terminals, or parts with high-voltage hazard signs. IMPORTANT: • The b

6 Figure 3 Installation flowchart

7 Installing the router Mounting the router on a workbench IMPORTANT: • Reserve a space of 10 cm (3.9 in) around the router for heat dissipation. •

8 Figure 5 Wall-mounting the router Installing the router in a rack IMPORTANT: To avoid damages to the router and mounting brackets, do not place

9 Figure 6 Marking installation holes for cage nuts 2. Install cage nuts on rack posts, as shown in Figure 7. a. Insert one ear of a cage nut int

10 Figure 8 Securing mounting brackets to the router 4. Use M6 screws to secure both mounting brackets on the router to the front rack posts, as s

11 Attaching the ring terminal 1. Cut the grounding cable as appropriate for connecting to the grounding strip. 2. Peel 5 mm (0.20 in) of insulatio

12 Figure 11 Connecting the grounding cable to the router Figure 12 Grounding the router through the rack

Copyright © 2014, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted

13 Figure 13 Connecting the grounding cable to the rack Grounding the router to a grounding strip 1. Remove the grounding screw from the router ch

14 Figure 14 Grounding the router to a grounding strip Grounding the router to a buried grounding conductor If the installation site has no groundi

15 Figure 16 Installing a WLAN antenna Connecting interface cables Connecting an Ethernet cable to a copper port Because fixed Ethernet ports suppo

16 3. Insert LC connectors of the optical fibers to the Rx and Tx ports of the transceiver module. 4. Connect the other ends of the optical fibers

17 Figure 19 Connecting a USB device Connecting the console cable and setting terminal parameters Connecting the console cable CAUTION: When usin

18 Setting console terminal parameters 1. Select Start > All Programs > Accessories > Communications > HyperTerminal. The Connection Des

19 NOTE: To restore the default settings, click Restore Defaults. Figure 23 Setting the serial port parameters 5. Select File > Properties i

20 Figure 25 Setting the terminal emulation parameters Connecting the power adapter The router's power adapter converts AC power to DC power,

21 Figure 26 Connecting the power adapter Verifying the installation After you complete the installation, verify that: • There is enough space aro

22 Booting Normal Extend BootWare Do you want to check SDRAM? [Y/N]

Preface The H3C MSR800 Routers Installation Guide includes five chapters, which describe the preparing for installation, installing the router, troubl

23 Power-on check After powering on the router, check the following items: • The LEDs on the front panel are normal, as described in "LED descr

24 Troubleshooting IMPORTANT: • The barcode on the router chassis contains product information that must be provided to local sales agent before yo

25 No response from the serial port If the serial port does not respond, verify that the serial cable is in good condition and the serial port settin

26 Reset button usage guidelines An MSR800 router provides the Reset button. You can use the button to reboot the system or restore the factory setti

27 Appendix A Chassis views and technical specifications Chassis views The figures in this appendix are for illustration only. MSR800 Figure 27 Front

28 MSR800-W Figure 29 Front view (1) Power receptacle (2) GE LAN ports (GE1 to GE4) (3) GE WAN port (GE0) (4) GE WAN fiber port (SFP0) (5) Console

29 Figure 32 Rear view (1) Grounding screw MSR800-10-W Figure 33 Front view (1) Power receptacle (2) GE LAN ports (GE2 to GE9) (3) GE WAN port (G

30 Item MSR800 MSR800-W MSR800-10 MSR800-10-WUSB port 1 1 1 1 GE WAN port 1 1 2 2 GE LAN port 4 4 8 8 SFP port 1 (Combo) 1 (Combo) 1 (

31 Appendix B LEDs LEDs MSR800 Figure 35 Front panel LEDs (1) GE port status LED (yellow) (2) GE port status LED (green) (3) System status LED (

32 MSR800-10 Figure 37 Front panel LEDs (1) GE port status LED (yellow) (2) GE port status LED (green) (3) System status LED (4) VPN LED (5) Co

Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a ro

33 LED Location Status DescriptionFlashing green (8 Hz) The system software image is being copied and decompressed. Flashing green (1 Hz) Comware ha

34 Index A C I L P R S T A Antenna specifications,30 C Chassis views,27 I Installation accessories and tools,3 Installation flowchart,5 Installation

Technical support [email protected] http://www.h3c.com Documentation feedback You can e-mail your comments about product documentation to [email protected].

iii Contents Preparing for installation ··············································································································

iv Appendix B LEDs ···································································································································

1 Preparing for installation Safety recommendations WARNING! Before installation and operation, read all of the safety instructions in Compliance and

2 Gas Max. (mg/m3)NH3 0.05 Cl2 0.01 To prevent overheating: • Provide adequate clearance for air flow, including at least 10 cm (3.94 in) ventilatio