H3c-technologies H3C WX5500E Series Access Controllers Uživatelský manuál Strana 106
- Strana / 221
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
95
Figure 24 Network diagram
Configuration procedure
1. Configure VLANs and VLAN member ports. (Details not shown.)
Create VLAN 10, VLAN 20, and VLAN 30 on Device A and Device B, create VLAN 10, VLAN 20,
and VLAN 40 on Device C, and create VLAN 20, VLAN 30, and VLAN 40 on Device D.
Configure the ports on these devices as trunk ports and assign them to related VLANs.
2. Configure Device A:
# Enter MST region view and configure the MST region name as example. Map VLAN 10, VLAN
30, and VLAN 40 to MSTI 1, MSTI 3, and MSTI 4, respectively, and configure the revision level
of the MST region as 0.
<DeviceA> system-view
[DeviceA] stp region-configuration
[DeviceA-mst-region] region-name example
[DeviceA-mst-region] instance 1 vlan 10
[DeviceA-mst-region] instance 3 vlan 30
[DeviceA-mst-region] instance 4 vlan 40
[DeviceA-mst-region] revision-level 0
# Activate MST region configuration.
[DeviceA-mst-region] active region-configuration
[DeviceA-mst-region] quit
# Specify the current device as the root bridge of MSTI 1.
[DeviceA] stp instance 1 root primary
# Enable the spanning tree feature globally.
[DeviceA] stp enable
3. Configure Device B:
# Enter MST region view, and configure the MST region name as example. Map VLAN 10, VLAN
30, and VLAN 40 to MSTI 1, MSTI 3, and MSTI 4, respectively, and configure the revision level
of the MST region as 0.
<DeviceB> system-view
[DeviceB] stp region-configuration
Permit: all VLANs
P
e
r
mi
t:
V
L
A
N
s
2
0
a
n
d
3
0
P
e
r
mi
t
:
V
L
A
N
s
1
0
a
n
d
2
0
Permit: VLANs 20 and 40
Permit: VLANs 20 and
30
Permit: VLANs 10 and
20
Device A Device B
Device C Device D
GE1/0/3
G
E
1
/
0
/
2
GE1/0/3
G
E
1
/
0
/
2
GE1/0/3 GE1/0/3
G
E
1
/
0
/
2
G
E
1
/
0
/
2
MST region
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Související produkty a manuály pro Směrovače H3c-technologies H3C WX5500E Series Access Controllers
(4 stránky)
(18 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce