H3c-technologies H3C WX5500E Series Access Controllers Uživatelský manuál Strana 21
- Strana / 221
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
10
Table 1 Actions to take upon detection of a loop condition
Port type
Actions
No
p
rotective action is confi
g
ured
A
p
rotective action is confi
g
ured
Access port
• Place the receiving interface in controlled
mode. The interface discards all incoming
packets, but still forwards outgoing packets.
• Generate traps and log messages.
• Delete all MAC address entries of the
interface.
• Perform the configured protective
action.
• Generate traps and log messages.
• Delete all MAC address entries of the
interface.
Hybrid or trunk
port
• Generate traps and log messages.
• If loopback detection control is enabled,
place the receiving interface in controlled
mode. The interface discards all incoming
packets, but still forwards outgoing packets.
• Delete all MAC address entries of the
interface.
• Generate traps and log messages.
• If loopback detection control is
enabled, take the configured
protective action on the interface.
• Delete all MAC address entries of the
interface.
Configuration restrictions and guidelines
• To use loopback detection on an Ethernet interface, you must enable the function both globally and
on the interface.
• To disable loopback detection on all interfaces, run the undo loopback-detection enable command
in system view.
• To enable a hybrid or trunk port to take the administratively specified protective action, you must use
the loopback-detection control enable command on the port.
• When you change the link type of an Ethernet interface by using the port link-type command, the
switch removes the protective action configured on the interface. For more information about the
port link-type command, see Layer 2—LAN Switching Command Reference.
Configuration procedure
To configure loopback detection:
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Enable global loopback
detection.
loopback-detection enable
By default, global loopback
detection is disabled.
3. Enable multi-port loopback
detection.
loopback-detection
multi-port-mode enable
Optional.
By default, multi-port loopback
detection is disabled, and the
device can only detect single-port
loopback.
4. Set the loopback detection
interval.
loopback-detection interval-time
time
Optional.
The default setting is 30 seconds.
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Související produkty a manuály pro Směrovače H3c-technologies H3C WX5500E Series Access Controllers
(4 stránky)
(18 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce